Advice 1: How to find women's shorts

Shorts – the perfect outfit for the beach, office, only need to choose the right model and fabric. To find the shorts on their own will, even a beginner seamstress.
You will need
  • - a large sheet of paper;
  • - pattern-based trousers;
  • pencil;
  • - the range;
  • - a pair of scissors.
Instruction
1
To build the pattern of the shorts, you need to create pattern-based classic women's trousers. The instructions on how to build it, http://www.kakprosto.ru/kak-91888-kak-postroit-vykroyku-klassicheskih-bryuk. After she is ready, you can start modeling for future shorts.
2
Measure the length of the product. It may vary from knee length to mid thigh. The waist line was lower by 3-5 cm
3
Mark the line of the pocket on front part. Draw a diagonal line, departing 3 cm from the lateral line towards the middle and 12-15 cm down.
4
If you wish your shorts were a little flared and a free draw from the Darts in a straight line. Cut the part along this line and spread, and the point on the waist line must be aligned.
5
Build the detail of the burlap pocket. Attach a sheet of paper detail of the front and circle line entrance to the pocket. Step back from the top 2 cm to the side and from the lower 6-7 cm to the side and 2-3 cm down. These points connect smooth lines.
6
Make pattern belt and belt loops. The pattern of loops is a rectangle 3x5 cm zone is a rectangle with its length equal to the circumference of waist plus 6 cm and a width of 6 cm Width of the finished belt will be 2 see If you want to carve out a wider zone, respectively, increase the width of the part. It should equal the desired width of the belt multiplied by 2, plus 2cm for allowances.
7
Paper pattern shorts ready. Put her on the wrong side of the fabric and draw a chalk. All parts are cut out, leaving allowances for seams at 1 cm on the side of cut and the waist line. For bended form the bottom, leave 3-4 cm belt Detail and belt loops cut out without allowances (they are built into the pattern).
8
Burlap pocket will have plenty of lining fabric, and the area of the side seam above the entrance to the pocket from the main.

Advice 2: How to build the pattern of the shorts

Shorts are a summer clothes. In addition, they are in daily life convenient and comfortable, at home, or, for example, sports training. However, their main purpose summer wear for different occasions. Women's shorts come in a variety of sizes and shapes – breeches below the knee, mini, loose, fitting, classic denim. In order to stand out from the crowd it is better to sew them yourself.
You will need
  • graph paper for the construction of the pattern; ruler; pencil; scissors; pins; fabric – 1 m; elastic waistband; fleece; zip-fastener (14 cm); decorative button
Instruction
1
Produced using the tape measure the following measurements: the length of the shorts; waist circumference; thigh circumference; the circumference of the girth of the place where the length of the shorts. For the construction of the pattern of the shorts, you need to decide what kind of fabric will be produced the shorts and which model you prefer. After that, go to the construction of patterns.
2
Build the pattern of the trousers the correct model. The construction pattern of the shorts is based on the transformation of the pattern of the pants. And then, on the basis of the created patterns raschertite the pattern of the shorts. To do this, spend a horizontal line across the pattern long pants (the distance depends on the desired long shorts). Then cut the lower part of the pattern (final long leg) and attach a new piece of graph paper to create a pattern roll edge, at what width should be slightly greater than the width of the leg produced a short line final length.
3
Swipe below the final length of the shorts three parallel lines. One draw at a distance of 4 cm from the line of finite length, the second, retreating to 4 cm from the first line, and a third, departing at 2 cm from the second line. All the extra paper below 3 lines cut. Then fold the pattern at the location of the three drawn lines. Note the continuation of the edge line with the main patterns of the shorts on podvoroty. And again cut all the excess paper along this line.
4
Transfer the completed pattern to the fabric, to do this, apply a paper pattern directly onto the fabric and cut out all of the details on the fabric, adding 1 cm from each edge of the fabric for seams. Then connect all the details of the stitches, while not touching the podvoroty. Then prostrochite all the edges of the joint on the machine and secure podvoroty, prostraciya through the continuation of the seam which connects the parts of the shorts. Then insert the zipper, prostracii machine stitch from the wrong side and sew a button.
Search
Is the advice useful?