Advice 1: How to make a case for speakers

When speakers get old, you want to overwrite them. The sound gradually begins to move in a sharp or crackling sound that brings some inconvenience when listening to that particular music track. In the home make a simple enclosure for the speakers.
You will need
  • Speakers, metallic fine mesh, glue, tool set, scissors, acrylic, organic glass, compass, pencil, sandpaper, a fan, a box of disk.
Instruction
1
First disassemble the design of columns.
2
Make acoustic wire disconnected from the Board using the connectors.
3
Use templates with which you will be able to cut parts from acrylic. To do this, apply the compasses and pen to future housing had right angles.
4
The finished wall is undercut.
5
Undercut organic glass with sandpaper.
6
Cut a hole for the speaker.
7
If you decided to work with the fan, and you need the mesh, cut to fit the wall of the housing, as well as screws. Secure the mesh with screws.
8
For the manufacture of the grille on the fan, use a box from a disk. Cut out its contours and undercut sandpaper.
9
Cut two grilles for the speakers on the front wall speakers. For this you will need a box from a disk.
10
Connect with glue, mesh and grid to create a front panel housing.
11
At the base should make holes for the wires and LEDs (4 pieces).
12
Glue all parts to the caseand are kindly requested to return all the internal contents of the columns.

Advice 2: How to make a loudspeaker

In our time, the choice of speakers is huge. Going to a specialty store, you will find everything your heart desires. However, it is always nicer to do things with his hands, because then they become dearer to you and to use them you will be more likely.
You will need
  • - nails;
  • - copper wire;
  • - hammer;
  • - pushpin;
  • a basis for the column;
  • Wat.
Instruction
1
Select the basis for future columns and speakers. As the basis columns use a stand for pencils, speakers take two.
2
Make a speaker yourself. Determine what you need the speaker height, then take a nail and cut it so that it was slightly less than the height of the speaker. The side you cut, grind, file the order that it was smooth. Then, on the part of the nail, which with the hat, wrap the copper wire in enamel insulation.
3
Take two buttons and smash them with a hammer until it becomes thick as foil. This will be the base. Nail glue to the base, the clip. Take a magnetic tube, the height of which should be slightly greater than the height of the nail with coil and wide, that there took place a nail. Install a nail with a coil in the center of the magnet and glue to the base. Put a plate of paper clips on a magnet on top. Speaker ready.
4
A compass on the paper draw a circle with the speaker of the circle was a bit less dynamics from the outside. When the speaker drew a circle, cut it out with scissors and attach to the front of the stand where you will attach the speaker. Circle the Foundation circle. On the stand you get a circle where you place the speaker.
5
Make a cut out for the speaker at the circled loop in the column. Did you make the base of the speaker with the opening for the speakers. Through the opening guide wire for the speaker, the rest of the space fill conventional cotton.
6
Assemble the column as a whole. To assemble the column into one use the glue - time. Insert the speaker into the base, apply glue to the edge on the inner side of the speaker. After applying the adhesive to a speaker does not fall and held on tight, leave it for a couple of hours.
7
Connect the column to the source. Before connecting, make sure that the glue has dried. Connect the wire you brought through the base of the speaker to the source. If you know anything about electrics, can do it easily. Column.
Note
Be careful when working with glass and creating patterns. Better prepare a compass and writing materials to all the edges of the future of the housing were smooth.
Useful advice
To get great sound out of the speakers, you need a good case. You can use the sieve as mesh for the front panel.
Search
Is the advice useful?