Advice 1: How to reflash the phone

Often for the correct operation of cell phone is required only to correctly reflash it, and this does not have to pay a certain amount of money to the service center. It is sufficient to carry out a few simple manipulations – and phone again in working condition.
You will need
  • Program firmware for phone or smartphone, Crack for Phoenix 2.5 a (230 kb) 2004 Phoenix (67.4 MB) Diego_3_06 (35 MB) and the drivers for the cable.
Instruction
1
Begin the installation programs in the following order: Diego_3_06.msi, then simply run (without installation) Crack.exe and put Phoenix in 2004. Get the message from the system that an error occurred and then have both Windows (with the error and Crack.exe – install) and click on Retry, while establishing our Crack.exe. If the program will require the replacement of all the files agree with it. Try to install quickly in order to prevent the repetition of mistakes. Do not pay attention to the different Windows with warnings!
2
The installation is finished and you receive two messages - Add Phoenix icon to Desktop (check boxes) and Open the log note! Then, reboot our computer by clicking on Finish.
3
After reboot PC, start Phoenix and immediately turn off his window. Turned? Now start to install phoenix.exe. Set? Well. Now the computer suggests a reboot, but agree it should not be.
4
Now install the cable driver for your phone. Next, you should copy the files with the extension .adl to the folder where you installed Phoenix. To find those you need on your C: drive in program files. The program for updating the firmware is ready. Remember that it works only until the first reboot.
5
Then run Phoenix. Click on File => Link, and then on Add. A window will appear, select Manual, then Next, then USB and click on Finish.
6
Now we have to connect our phone to PC (via cable) and wait until the PC detects the phone and installs the driver. Then we go into Phoenix and click on File => Scan Product (Ctrl+R).
7
Now, just flashing. Unpack the new version of firmware that we downloaded the wound and click Phoenix top Flashing => SW Update (Flashing to Update), then in the window that appears, click on the Image file — the firmware File (*.C0R) and select the PPM File Is the Language pack (*.vXX, XX the number of the package.). Then click on Start. When you receive the message Test mode without disconnecting the unit from the PC, you need to enable it and close the message Test mode.
8
Reboot again, and finally the message that flashing was successful. Now our cell you can safely reboot and format.

Advice 2: How to flash htc sensation

For flashing phone HTC Sensation uses a special application package for Android developers SDK Tools. The firmware is in service mode of the phone through normal USB cable that came in one package with the device at purchase.
You will need
  • - firmware file;
  • - Android SDK Tools;
  • - HTC Sync.
Instruction
1
Before re-flashing, download the latest version of software available for HTC Sensation. To download you can take advantage of the resources on the software for this phone. After downloading the appropriate archive with the firmware, unzip it using an archiver to a folder on the computer.
2
Download the Android SDK from the official Android. Install the received software package using the installer. If you have not installed HTC Sync, make its installation, because along with it comes a package of all the required drivers for flashing.
3
Put the phone in Fastboot mode. To do this, turn off your HTC, and then remove the battery and reinsert it into the machine. Turn on the smartphone, while simultaneously holding the power button and side volume down key. Wait until you see the selection menu of boot options. Among the proposed options, select Fastboot using the volume buttons. Confirm your choice by pressing the top power button.
4
Connect your smartphone to the computer and wait for unpacking the right drivers. Run the program adb.exe you can find in the folder with control software for Android ("start" - "Computer" - "Local disk C:" Program Files – Android – SDK – WindowsPlatform - Tools – ADB). Start adb.exe you can make clicking on the right mouse button on the file and selecting "Run in command prompt".
5
Enter the prompt fastboot oem get_identifier_token and press Enter. Copy the result from the operation key on the official HTC website in the section unlocking the device for which you will need to register by filling the required fields. After the transition to Step 10 paste the code from the command line in the appropriate section and click Submit.
6
On your phone have the unlock code in the format unlock_code.bin. Download this file and place it in the same directory where is located adb.exe. In the command prompt, type fastboot flash unlocktoken unlock_code.bin. If the operation was done correctly, you will see a corresponding message on the screen of your device. Select Yes.
7
Next, enter the query:

fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot flash boot boot.img
fastboot flash userdata data.img
fastboot reboot

After the introduction of these commands the device will restart and the new firmware will be installed on the device.
Note
It is recommended to download and install only the official firmware files to avoid possible difficulties in using or maintaining your phone in the future.
Is the advice useful?
Before flashing, save all your data on your computer, because in the process of installing new software they will be lost. Save your important data will help the program HTC Sync.
Note
Keep in mind that after flashing you will not be able to return to the previous version, the number when the replacement can only improve, but not Vice versa. The old firmware simply "kill" the device, and then have to carry it to the repair... Besides, not the fact that a jailbroken phone will work without the "hatches".
Useful advice
To get started is to uninstall PC Suite (if it was installed previously). Then find and download the following programs that we will need for the job.
Before you start flashing, don't forget to remove the memory card from the camera and the phone itself to format. The phone battery should be fully charged. By the way, if on the PC running the screensaver, it is also better to temporarily disable. And, finally, disable the Defragmenter OP, etc.
Search
Is the advice useful?