Advice 1: How to knit plaid

To tie the blanket, you need to choose a model that you can find in any magazine or book on knitting.



To achieve the desired future size of the blanket is the traditional method of add / remove several loops or entire rows, or to add or omit from the squares. To adjust parameters you need to take the yarn of a different weight or to use a different number of spokes. In the calculations it is necessary to remember the number of stitches for a border.




As a rule, plaid knit as a canvas, so before you start, you need to make sure that the appearance of the product was neat.



  1. You need to remember that the reverse side of your rug will also be visible. Therefore, it is preferable to use two-way binding that will look good on both sides.

  2. In order to give your product a neat appearance, you can sew the finished blanket edge.

  3. A new thread is added in the place where you can hide it with the edge.

  4. A delicate fabric lining will be very practical decoration of any plaid.


There are several methods to bind a blanket: squares, strips and parts, the piece or pieces. If you decide to knit a blanket in one fabric is knit in two directions on long circular needles, which contain a large number of loops. To ensure the smooth surface of the canvas can special banding – it can be dialed together with the main fabric or just on the edge when your product will be ready.




Plaid, consisting of several separate fragments, you can knit on the go or to share its production on a couple of people. In this method the components of the plaid are knitted separately and then combine them into one painting. For the connection of fragments you can use a contrasting thread. Assembly is done in three ways:



  1. Traditional stitch used to knit sweaters.

  2. Crochet – style without adding and prostovisa.

  3. Decorative stitch, for example – over the edge, zig-zag stitch.


The wet processing of the plaid is the best method to create fragments of knitting in the required forms and to align their edges. However, not all types of yarn should be applied wet processing.

In wet processing without the use of iron, the blanket is attached to the flat surface of the conventional pins – so it will take the desired shape. The product must dry. Knitted plaid iron is not needed, otherwise all the loops could lose some texture.

Advice 2: How to knit a blanket with needles

Handmade things are always valued higher than store-bought, especially if the mistress puts them in his soul. This postulate applies to the blanket, which will easily be able to bind to the spokes for even a beginner.
You will need
  • circular or regular knitting needles;
  • - a few skeins of thick yarn of the same or different colors;
  • - the range;
  • hook.
Instruction
1
Before you start, you should determine the size of the future product. The standard ratio is 1.6 to 2 m. If you want the edges of the blankets covered the armrests and hung from the sofa, then these options are added at 30 cm On the spokes recruited about 50 turns, which fit the sample length of 10 cm It is necessary to find such values as the number of loops in one centimeter. Then you can calculate how much you will have to get the hinges to get the edge is 1.6 m. for Example, from 50 turns happened 20 cm Divide the first number by the second and get a 2.25 loop in 1 see That is 1.6 m will be of 2.25 multiplied by 160 is 360 loops.
2
The simplest patterns are the garter and checkerboard binding. It is not recommended to knit a blanket in only the front loops, as its edges are bent inside. Knit garter is an alternation of front and rear series on the one hand, that is, pravasa the front loops of one row and turning the product, the reverse side also perform facial loops. The checkerboard consists of diversified one of the rectangles. For example, in the first row alternate with 5 loops front and back, then continue with 6 rows, 7-m – change loop.
3
For work it is necessary to buy circular knitting needles on the line, as in this case, you do not have to interconnect the small details. Optional knit in one color, skeins of yarn can be alternated by combining several shades of the same color or contrasting colors. If the product runs garter viscous, then on the front side of the strips will be straight, while the reverse is blurred. In a checkerboard pattern both sides get the same. Typing about 300-350 loops must, in compliance with the order of front and rear loops and alternating colors, knit into the entire length of the blanket. The ends of the different coils it is better to connect on the edge, since nodes are less visible and partly hidden by the fringe.
4
If, instead of circular needles, use a normal pair, the blanket will be composed of many squares that are sewn together crochet. Their pattern may not match, it will give additional texture to the piece, like a patchwork. Besides, if all the details associated facial pattern, alternating between them in normal and inverted position, the plaid will be a big checkerboard. The edges of the elements bent in one direction, which will later reverse. Edge tied off with a hook, you can add a fringe of chopped strands.
Search
Is the advice useful?