Advice 1: How to replace bulb on a Hyundai Accent

The car under the brand name Accent ("Accent"), which produces Hyundai, belongs to the class C. the machine has two block-lights which include bulbs head and tail light and turn signal. Fog lights consist of halogen lamps, lamp "indicator" - single-strand with orange bulb. Also, the car can be equipped with fog lamps. If any lamps fail, it is important to know how to quickly and correctly replace.
Instruction
1
To replace lamp head light, remove the battery. Carefully hold the rear portion of the lamp and disconnect the connector wires. Remove the rubber cover and remove the locking pin from engagement with the hook. Take him to the side and remove bulb from the headlamp housing.
2
Do not touch the halogen lamp, because the marks will darken when heated. This, in turn, will cause rapid failure of the lamp. Clean the terminals with alcohol and a clean rag.
How to replace <strong>lamp</strong> Hyundai Accent
3
To replace bulb marker light disconnect the connector wires, which is suitable for marker lights. Turn the bulb bulb counterclockwise at an angle of about 45 degrees and remove it from the housing. The indicator lamp is removed the same way: turn the bulb bulb and pull it out. Click on the lamp, turn it until it stops.
4
To replace bulb marker light and lamp brake in the tail light Unscrew with a screwdriver the two screws with which the headlight is attached to the body. Slide the lantern to the side and print two pin holder-lantern eyes. Turn it counterclockwise cartridge and remove it.
5
Then click on the bulb and turn it until it stops. Remove the bulb from the socket. Please note the reverse setup that the tabs on the base of bulbs located at different levels and must exactly match the internal grooves of the cartridge.
How to replace <strong>lamp</strong> Hyundai Accent

Advice 2: How to replace the belt on a Hyundai

Reasons for replacement of timing belt (camshaft) driving a Hyundai may be a few: cracks, tears or other damage after the mileage reached 60 thousand. km. In any event, removal and replacement of the timing belt should be preceded by a thorough inspection.
You will need
  • - wrenches;
  • - screwdriver;
  • - carpenter's knife.
Instruction
1
To replace the belt put the car on a viewing hole or overpass. Using the key 10 to loosen the four bolts on the pump pulley with the cooling fluid. Then you can remove he belt and accessories – drives alternator, air conditioning compressor and power steering pump.
2
Next completely Unscrew the bolts and remove the top cover. Using the key 22, loosen the bolt that secured the crankshaft pulley. If you have a car with a manual transmission, ask someone to hold the brake pedal if the gear is engaged to rotate the crankshaft.
3
Install the piston in the top dead point by turning the crankshaft until then while does not coincide with the mark in the form of the letter "T". When the mark on the camshaft bearing will coincide with the hole in the toothed pulley of the camshaft, loosen the bolt, remove the crankshaft pulley, washer and protective cover.
4
The key 10 to loosen the bottom cap, and a key 12 loosen tighten the adjusting bolt and mounting bolt. Then, jamming a screwdriver between the roller and the bushing, rotate to the left stop bracket tension pulley and loosen the belt tension and then tighten the adjusting bolt.
5
Then use a screwdriver to take out the oil pump body end of the spring, loosen the bracket bolt and carefully remove the tensioner pulley. When replacing castors you will also need key 12. Unscrew the bolt and remove the roller.
6
Installation spend in the reverse order. Before you install the belt, be sure to check that the timing marks on both camshaft and crankshaft coincide. Now install the belt on the crankshaft pulley and the camshaft so that the support roller the belt was tight.
7
Then loosen the mounting bracket bolt of the tensioner pulley and adjustment bolt. During this operation the roller locks in position, and the belt will gain tension. Rotate the crankshaft two times clockwise, using the retaining bolt of the pulley.
Search
Is the advice useful?