Advice 1: How to adjust the sight

Paintball is a very exciting experience simulating real military action. Two teams trying to "destroy" each other with markers shooting balls with paint. Thus the size and weight of the paintball guns can get close to the size and weight of military weapons. Realism can be added with the installation of the optical sight. But without its setting – it's just a telescope bolted to the body of the marker. Let's set sight.
Instruction
1
Set the marker on a flat surface, on a support. At the same time trying to make a support at waist height. It is important that the marker while aiming trembling in your hands. If you have a special tripod for the token – this is the perfect situation. But if no tripod, sand bags.
2
Prepare goal. As purpose, suitable folded sheet of cardboard. Draw in the center of the cardboard sheet the point that it was about a coin size. Put the target at a desired distance from the marker with a telescopic sight, which needs adjustment. Make sure that the target of anything fragile, and need not because the balls will fly through the cardboard through and through. Dig a target in the ground. If necessary, add to her stability.
3
Put on a mask, centering around the point the risks of sight without lifting the marker. Do three shots. Go to the target and is determined by the holes in the cardboard, which got our balls.
4
We need to adjust the point of contact of the balls. To do this, use the buttons vertical and lateral settings. The unit of measurement for the most part of buttons is the minute (MOA or 1 / 60th part of a degree). Usually four press of a button equal to one minute, which can move the point of impact of balls at 2.5 cm distance from the target in 91 meter. If the shots we have, say, were higher by 7.5 cm to the left of the target at 5 cm distance to the target – all the same 91 m), the lateral setting we need to switch to the right for 2 minutes, and the vertical down for 3 minutes.
5
If you shoot the target more remote, you may have to compensate for arc at which the ball will fly, small elevation of the sight. Unfortunately, this is a problem of all optical sights, mounted on the paintball marker.
6
Produced the necessary changes, then do three more shots. Check the result. If the setting of the sight still does not satisfy us, make more changes and check again.

Advice 2: How to adjust the sight a BB gun

The secret to accuracy is the shooter not only skill and a little flair, but also of the correctness and accuracy of settings is sightand. Professionals line up the sight quickly, but beginners are usually to work hard.
Instruction
1
The main setting of the sight is placed on the level. Well, if there is a special frame, equipped with bubble levels. It will secure the rifle and in the distance hung a plumb. Set the rifle in balance bubble. Look in the optics – you should see the aiming mark relative to the plumb line. If the vertical line of the aiming mark non-parallel to the string of the plumb, the sight is littered with left or right. To leave it is impossible, because then when shooting at different distances the bullet will deviate to the side.
2
Align the vertical stub of the aiming mark so that it was parallel to the string or rope plummet. To do this, loosen the hose clamps that tighten the brackets, and start rotating the optical sight as long as the thread of the plumb and vertical line of the reticle are parallel. Necessarily it is necessary to glance at the level bubble, because the level can be brought down accidentally. When the position of the sight is adjusted, the screws pull the clamps again. Now the sight is set correctly level.
3
When you put the sight on the level and he took his rifle in hand, you can mistakenly determine that a relatively rifle sight is crooked. Nothing terrible, just rails for optics are unevenly milled. Most importantly – the position of the plumb Bob relative to the aiming mark, as described above. So no need to put a target on the eye relative to the brackets. Otherwise the bullet will deviate to the side.
4
It happens that at hand base with level bubble no. Take a sturdy nylon cord that will not break under the weight of the rifle, and the same plumb. Loop the cord and attach the optical sight.
5
The other end of the cord attach for some emphasis. In short, hang the rifle horizontally. Let it be balanced in the vertical plane. It is important that the loop was keeping the sight over the center of gravity of the rifle. Let the rifle a little bite down or slightly lifts the trunk, but she must hang in the vertical plane.
6
Now put a vertical line of the aiming mark parallel to the thread of the plummet. Screws clamps loosen and tighten gradually and alternately in one or two turns, but not immediately one after the other. So you can warp. From one bracket move on to another until you tighten everything correctly.
Useful advice
Adjusting the sight, not to aim for perfect precision. Still, we are dealing with balls for paintball and not with real bullets. So from a small scatter, we can not escape.
Search
Is the advice useful?