Advice 1: How to sew a cap

With such simple details like a hood, you can save at any carnival. If you make the cap one color, you can dress up the baby gnome. And if you make a striped, everyone knows Pinocchio.
You will need
  • Fabric 50х70см; sewing machine
Instruction
1
Draw the pattern of the cap on the paper as shown in the figure.Transfer the pattern to the fabric with a piece of soap or chalk sacrosidase. Cut out detail from the fabric, leaving a seam of 1.5 cm on each side.
How to sew a cap
2
Fold the finished part in half face to face. Sew it on the side seam. The seam sewn on the machine or manually. Remove the cap on the front side. The bottom of the hood bend and prostrochite. Can be inserted into a hem of a bottom of the elastic cap loosely so that it rested on the baby's head.
3
To the tip of the hood need to sew on the tassel. It can be made from paper or from yarn. Brush from the paper is done as follows: a strip of paper (20 x 7 cm) cut parallel to the stripes (not reaching the edges). Strips 0,5-1 see them Roll into a tight tube and secure with tape or string. A tassel of yarn how: on the cardboard square-shaped wrap yarn (the more yarn, the more magnificent the will brush). Tie one side of the resulting beam thread, and on the other hand cut with scissors.

Advice 2: How to make a chef's hat

Chefs and cooks in fairy tales are quite common. Therefore, for school or home performance needs and appropriate costume. One of its main parts — the large cap, which can remove the hair even the Princess, under the Director's plan found themselves in the kitchen. To knit this hat can with your hands.
You will need
  • - white cotton fabric;
  • - cardboard;
  • - interlining;
  • - starch;
  • - sewing accessories;
  • - ruler, pencil and compass.
Instruction
1
Measure the circumference of your head. To cut the cap right on the fabric, but to someone who is not very big sartorial experience, it is better to carve out the right parts of paper. Most suitable graph paper. Draw a strip the length of which is equal to the circumference of your head. The width may be different, depending on the style of cap, but not less than 5 cm Strip of fabric should be folded lengthwise, so it will be 2 times wider. Draw a circle of a diameter approximately equal to the length of the strip.
2
Transfer the pattern to the fabric. It is best to use for these products, satin, calico or something like that. And fit the muslin, but in this case it is better to cut off a strip, folded four times instead of two. Not very suitable synthetic fabric. To outline the finer details on the reverse side. In a circle make an allowance of about 0.5 - 1 cm strips of fabric fold in half. Align the fold one of the long sections of patterns. For other parties to make an allowance of 0.5-1 cm Cut out of the workpiece.
3
Stripes reinforce the adhesive interlining in the entire area. Allowances can be not to glue. Fold it wrong side inside, align the cuts and zautyuzhte a fold line. Align the strip, fold it across the face inward. Sweeps and serecite short seam. You should have the wide ring. Fold it along the fold. Just made the seam should be inside the workpiece. Allowances on long sections zautyuzhte inside. You can do the job and in a different order. Glue the blank, fold and zautyuzhte allowances, and then sew a short seam.
4
The circle sew a seam "forward a needle" on the line that divides the surplus. Do not very large stitches. Will structure the item so that the length of the circumference equal to the length of the ring. Stock circle insert ring inside, baste and pristrochite close to the open edges of the strips. If the fabric is much bristling, cut the seam allowance corners, leaving to the circumference of 1 mm. Can be finished with a line of decorative stitching primaqiune. The hood is ready, but it must still rigidly starched.
5
Cook the paste at the rate of 2 tablespoons of starch to 1 liter of water. Hold it dome a few minutes to cloth soaked. Spread your product and put it on the disc (for example, on the right size Bank). Dry while the hood will be a bit wet. Iron and doushite on the disc.
Is the advice useful?
The hood can be decorated with lace or embroidery. Embroidery position on the outer part of the strip. To decorate this product need to build. Lace stitching or attach when participarii the upper part of the cover to the strip. Prepare a strip, attach the inside edge of lace or sewing and baste to the outside of the billet along its entire length. Then sew the top. This ornament looks better if it prisborivat.
Useful advice
To cap glistened, can sprinkle hair with glitter. Or embroider sequins. Or sew a tinsel.
Search
Is the advice useful?