Advice 1: How to sew a jacket the bat

Shift blouse "flying mouse" is almost never out of fashion. It looks stylish with pants and a skirt, you can wear it and with a strict suit. Such a versatile article of clothing can make even without a pattern. Like the clothes worn in medieval Japan, and sewed it from whole cloth. But if you first took up such a sewing or planning to sew silk, the pattern is better build.
You will need
  • cloth;
  • - graph paper;
  • pencil;
  • - the range;
  • - sewing machine;
  • - needle;
  • - thread.
Instruction
1
Remove the measurements. You need to know poluobhvat chest, the sleeve length from the neck to the lower edge, poluobhvat neck length, the length of the yoke and poluobhvat of the wrist or the hands of where to end the sleeve. Poluobhvat neck, divide by 2.
2
Put a sheet of graph paper vertically. Put at the intersection of the left white edge, and one of the thick lines point A. Aside from it to the right 1/2 poluobhvat neck. Select the point B. From it to the right will put the sleeve length and mark the point marked B. From point b down put poluobhvat wrist. This will be the point G.
3
From point A down aside the length of the yoke. Put a point D. measure From it to the right poluobhvat chest. You get the point E. Connect points E and G by a straight line. Find the middle and mark the point O. it will put up a perpendicular, mark on it of 15-17 cm, and denote it as O1. Through the points E, G and O1 of the arc, the convex part of which is directed to the left.
4
The neck on the back is a little less than on the shelf. Therefore, for a pattern make a drawing for the back and when cutting widen the cutout on the shelf 2 cm From the point And put down 4 see the resulting point connect point B of the arc. Cut out the pattern..
5
For belt take a rectangle whose length is full waist, plus 2-3 cm free customized fit, plus allowances for seams. Calculate the width, subtracting from the total length of the blouse length of the yoke. Multiply the result by 2 and add allowances.
6
Fold the cloth 4 times. Line the middle shelves (or back, as you like) must coincide with the fold equity. Depending on the variant of the pattern the shoulder line or combine with either cross-thread or cut it out shoulder at an angle. Draw around the pattern, leaving a small seam.
7
Cut out the details. There should be 2. Determine which is front and which is back. On the shelf, increase by 2 cm neck. You can make the center back slit to make it easier to handle bake the neck.
8
Fold belt in half lengthwise right side out. Zautyuzhte fold. Try on the belt. If necessary, mark the locations for the side recesses. This is usually required if Flirty short. Will astrocyte undercut.
9
Treat the neck with bias binding. If you have done the cutaway back, astrocyte it. Add up the parts, aligning the side sections. Baste the shelf with back and sostrochite.
10
Prostrochite the yoke on the bottom using large stitches or sew manually, seam "forward needle". In the second case, it is necessary to make the stitches smaller. Will the yoke structure. Baste to her belt, evenly distributing the folds. Sew the waistband.
11
Treat the bottom of the sleeves. If they are long enough, they simply sew on bent 2 times on the wrong side. Is that the fabric is narrow, and the sleeve you want to do genuine. Take a break and sew a cuff of the desired length.

Advice 2: How to sew a jacket

Sew the jacket itself is not very difficult, but to do this you need time and patience. But then you will be able to boast of a thing which no one else has.
Instruction
1
First you need to make a pattern. Usually pick a model from a magazine or the Internet. If in your wardrobe there is something similar that fits you well, you can use as the basis for this thing. If you took the pattern from a magazine, transfer it to tracing paper. Where the model beyond the sheet size, popliteus glue or tape another paper.
2
Carefully cut the pattern directly on the contour. If you have taken some thing from your closet, lay and unfold it on the tracing paper, trace the contour. The resulting pattern cut out.
3
Now you need to cut a jacket. Lay the fabric on a large table or on the floor. When cutting the symmetrical parts fold the fabric in half, face inwards. Lay the pattern on all the details. Between them there should be a distance to the seam, often it is about 0.5-1 cm In cutting work should take into account the pattern of the material.
4
If you have a piece of chalk in a contrasting color, it is possible to cut around the pattern. See that they were everywhere. To put the contours with the help of safety pins for sewing or laying snares. For the snares you will need a thread of contrasting color. Large stitches sew the edges of the pattern. The thread must be tight, every stitch should be as small loop.
5
After the circuit pattern printed on the fabric it should be cut. Place the seam on all sides. Groove cut is not necessary, but they must also be applied. If you laid a snare after cutting its parts apart halves as let loose stitches, and cut them in the middle on the front side of the fabric. In the end you'll have a contour, applied with the cut loops.
6
Cut the details you need to sweep. Fold them inside out and salivate pins for sewing or metyvit large stitches along the lines of the pattern you've done.
7
Measure what you get. If something somewhere isn't going to fit, strut is the place and sweeps already adjusted.
8
After you're satisfied with the fit on the figure, it can be contracepti on the sewing machine. Sostragivaja all on the same contours, which thing is already sour.
Note
Options ports may be different. Recently has become popular a large cutout, where when moving the top slide and exposed shoulder. In this case, you just need to trim the cutout to size. But be careful, he must not be too large.
Useful advice
The pattern can be constructed a little differently. From the point And put the right half of the poluobhvat neck plus the sleeve length, plus another 4-5 To see this point is swipe down perpendicular 5 cm Place the point B and connect it with the base of the neck.

Looks very good on this blouse a cowl neckline. The neckline in this case is also quite large. Take a rectangle with a width of 14-20 cm of the same fabric. Its length is equal to the length of the cut, but maybe a little more. Fold collar in half along the length. Zautyuzhte fold on the front side. Turn it inside out. Align the short sections and sew the seam. Align one of the long sections neck with folded detail front, baste and sew. The second cut, which was now on the wrong side, fold twice and also pristrochite, trying to get into the existing seam.

Original "bat" can be made from several identical variegated shawls. You will need 4 small pockets on the yoke 1 and the same on the belt and collar. Scarves fold in pairs, right sides to each other, trace the pattern and cut out details. A scarf designed for the waist, fold in half and cut. Sew strips. Fold the rectangle in half. Then sew the blouse as described.
Search
Is the advice useful?