Advice 1: How to fix the anchor

In order to in a concrete or brick base to secure an object, do not use the materials at hand or nail. It is better to use effective mounting of the part anchor. In translation from German this word means "anchor". Thus, the anchor lives up to its name. It is securely and firmly holds any items for any reason. In construction there are different types of anchors.
Instruction
1
Take drop-in anchors with internal thread LA, LAH. This type is the simplest. It is used for the installation of stone, brick or concrete structures. Assembly is performed in a pre-drilled hole of the required diameter and depth. It clean - this must be done for any type of anchor. Install into the hole and screw it. Reliable degree of fixation is achieved by unclamping the fastener. The same type multifunction anchor MTA, which is used for bases having internal cavities.
2
Take a wedge anchor, which is produced by hot-galvanized, acid-resistant and zinc plated. It is equipped with a special wedge, extending in the installation process and fixed in the nest. Enables end-to-end installation through installed on the base material. Place it in the prepared hole, then hammer a hammer and tighten with a wrench. To similar type fasteners applies a screw anchor. They are equipped with a screw with countersunk head head. This gives the opportunity to use them when mounting door and window frames. The wedge anchor is securely fixed in design as you tighten the screw.
3
Install the rod retainer. It operates on the principle of the V-anchor, is designed for deep installation through several consecutive layers of insulation and cladding. An additional advantage of this product is the ability to set it at an angle. Such a rod clamping mechanism in the socket with the help of the expanding wedge is used in the anchor TA. The part with internal thread together with the rod which can be cut if necessary to desired length, used for mounting several layers of material. Hammer the anchor into the prepared hole, fix the fixable material on the rod with a washer and nut.
4
Install the anchor PFG with screwing. It has an internal thread, and in the process of installation, the plug-in elements are extended and firmly fixed in the nest. This product can be used in combination with inserted conical bolt, bolt with loop and hook-shaped head or with inserted liners. PFG anchor is used for solid grounds.
5
Install brass anchor MSA by screwing. Suitable for use in a brick or concrete Foundation. Its the brass sleeve has an internal cavity of conical shape (with thread), tapering to the tip. As you tighten the screw it is distributed in width and securely pressed against its rough walls to the inside of the holes in the base.
6
Take for gypsum panels anchor DRIVA. It is made in 2 versions: nylon and zinc alloy with aluminium. A metal option is suitable for particleboard. Screw his power tool right into the base, therefore he does not need pre-drilling. Then install and fasten the material and screw in the anchor screw.
7
Install the anchor bolt, which is considered one of the most reliable in the mounting construction of the tools. This specific type of fasteners, which cannot be substituted by neither plug nor the usual nail. Usually anchor bolt attaches the equipment that connects the building constructions and concreted, sometimes laid brickwork. It is used in various fields - mount pendant fixtures and ceilings, doors and Windows, and when vertical installation. Method of installation: drill a hole with a diameter that matches its outside diameter. Clean the hole from dust and insert the anchor bolt, with a little raskladov the sleeve. Installation is considered ideal when it is embedded in a level concrete or flush. Setting the anchor in the concrete, tighten bolt head.

Advice 2: How to fix anchor bolt

The anchor plays a very important role regardless of what element of construction it is a machine that is installed on a concrete floor or boltsevye ladder mounted on the wall. It provides communication with the base, and if this relationship is fragile, the construction threatens the destruction, no matter how durable on the inside it was not. To be safe, the anchor should be set, following a particular technology.
Instruction
1
Chemical anchor is very durable and reliable. It can be installed in any material: brick, stone, cellular concrete, wood, etc. Since it's mounted with adhesive, it not only weakens the base, which is attached to, but in many cases makes it even stronger.
To install anchor, drill a hole the desired diameter at the desired depth. Clean it with the brush-brush, blow pump or a pear.
2
Fill 2/3 of the hole of the adhesive mixture of epoxy or polymer resin. A container of adhesive (cartridge) can be decorated differently – a syringe, a tube, etc., Different methods of mixing the components of the adhesive. Whatever the embodiment, the adhesive cartridge, you need to act strictly according to instructions attached to the product.
3
Twisting motion, install the anchor into the hole to the full depth. Remove drips of glue from the base. Time readiness anchor to the perception of stress depends on the brand of glue, it is specified in the instructions. After the specified time, the anchor can be fastened to any design.
4
Mechanical anchors are installed without glue. The principle of operation is based on the wedging of the sleeve anchor within the hole, and thus a reliable fixation in the base.
Drill and clean the hole the same way as described above. Through the mounted item, insert in hole wedge anchor and hammer it with a hammer until the nut abuts in fixed detail. Tighten the nut with a necessary (but not excessive) effort. Over tightening the end anchor rasklinivat sleeve and securely fixed in the hole.
5
Ways of wedging may vary. If it is a special rod that is inserted inside the anchor, then after the installation of the bolt in the hole and hammer the rod with a hammer inside. Thus, you will ruskinite the bushing and lock the anchor in the hole.
6
To install wedge anchor with internal thread, special tools are needed – a rod, similar to a center punch or a piercer.
After install the anchor into the hole, place the tool inside and hammer rackline sleeve. Then remove the punch-piercer and screw into the threaded hole anchor mounting screw.
7
The so-called frame anchor has two rasklinivanija zone in the base and anchoring details.
The frame and hammer the anchor into the ground via a dockable item. Tighten the screw with the required effort. In this first raskinetsya lower in the base part of the anchor, then the top, in detail. In the result, the latter will be firmly attached to the base.
8
Purchase products use very convenient, especially if you have to install a large number of anchors. However, if necessary, can be firmly fixed in any ground, and improvised explosive device – a bolt or rod of any kind.
9
Drill a hole with a diameter of 1-2 mm larger than the anchor diameter. Well clean the hole from dust and crumbs. Fill the hole halfway or a little more epoxy or putty with hardener. Rotational motion and easy blows of a hammer, install the anchor into the hole. Remove drips of resin. Some time later, when the epoxy a bit (but not completely) harden, flatten it around the anchor flush with the base. To use this anchor in about a day.
Note
Anchors exist in different versions, such as: anchor bolt (or anchor bolt, which is also called wedge anchor or wedge anchor), anchor drop, the anchor frame. Then in this hole is screwed a nut or bolt. In the case when the nut is screwed, the rod is pulled out. It is possible to fasten another part. In cases where the bolt is screwed, the rod remains inside.
Is the advice useful?
How to fix anchor bolt in the wall of concrete and brick? The process takes a little time for the task You will need a drill, hammer, anchor bolt. Ensure in advance the material that will be attached to the bolt was not loose. Anchor bolt with nut — the principle of operation is the same as the regular anchor, added a thread that comes out when you twist the head of the bolt.
Search
Is the advice useful?