Advice 1: How to turn on nokia without the power button

Nokia phones have the power button, usually located in the upper part of the body. Quite often she pressed inside, crashes or just stops working. To turn on the phone in this case, it is possible in several ways.
You will need
  • - tweezers;
  • - thin, not an isolated transaction;
  • thin screwdriver;
  • - soldering iron with a fine tip;
  • - soldering flux;
  • - lamp with a magnifying glass.
Instruction
1
Tweezers or any sharp object remove the non-working button of the phone body. Light flashlight or lamp, a hole in the hull. You will see a rectangular area of the Board, the appropriate size button and 2 contacts on each side of him. A fine wire, needle or pin lock any pair of the side contacts. Be careful not to advance the needle or pin into the hole, otherwise you'll damage the contacts below. Subsequently, do not turn off the phone and do not allow complete discharge of the battery.
2
If you cannot remove the button, remove the phone case. To do this, using a special thin screwdriver remove all the bolts, then carefully lift the back cover. Remove the jammed button.
3
Take a soldering iron with a fine tip. Plug it into an outlet. Dip the heated tip in soldering flux. For better visibility light fee special lamp equipped with a magnifying glass. Take the button with tweezers. Solder it to the contacts on the Board. Do not overheat when soldering the button and pay, otherwise they may melt. Do not leave the jumper between the contacts.
4
If you don't have a soldering iron and flux, then just short the button contacts off with a thin metal object as described in the first step. When closing with one hand, hold the battery so that he fell and the phone went off again.
5
Replace rear panel and tighten all the bolts.
6
If the button is lost, then solder to any pair of the side contacts on the Board posting thin. Their length should be 10-15 mm. Print of the wiring outside the case. Slide the rear panel and install the bolts. To turn on the phone just short the soldered wiring.
7
If the individual attempts to switch on the phone were unsuccessful, contact the service center or repair shop.

Advice 2: How to turn on nokia without button

The Nokia phones the power button is usually located in the upper part of the body. Over time as the operation of the phone, this button may push and stop working. In this case, to switch on the phone, will have to resort to little tricks.
Instruction
1
Take tweezers or any sharp object to turn on Nokia without button. Remove from the body of the phone is non-working button. Take a flashlight or lift the phone to light. Carefully inspect the place of Posada buttons. You should see a hole in the hull, and charge with four contacts. Take the tweezers, a pin, a needle, or any other thin metal object. Lock any pair of contacts.
2
Observe the greatest caution. Do not put your metal object too far into the hole so as not to damage the Board phone. After you complete the contacts, the phone will turn on. Not to do this again, do not allow complete discharge of the battery and do not turn off the phone.
3
Remove the case from your phone, if you can't remove the button. Take a set of fine screwdrivers. Choose a suitable one and remove the mounting bolts. Then lift the back cover. Using a needle, tweezers or any other object remove the damaged button from the phone. Next, you'll need a soldering iron. It is desirable to use a soldering iron with a narrow tip, since there is almost jewelry work.
4
Insert the soldering iron into a power outlet and wait until it warms up. Then take resin or soldering flux. Dip them in the soldering iron and solder the button to the Board to include Nokia. Be careful. Be careful not to overheat the Board or button as they are made of plastic and can easily melt.
5
Also make sure that between the contacts of the left jumpers to avoid shorting. If you don't have a soldering iron, after you remove the button, simply close either pair of contacts, as described above. Hold the battery so it wouldn't slip. Secure the rear panel of the phone, lock the mounting bolts. Make sure that the phone is completely discharged and not turn it off.
6
Solder to the contacts on the Board of two not very long wiring to turn on Nokia without button. If the button is lost, this is the best option. Solder wires to the two contacts. Get them over the phone. When you want to turn the phone on, just lock these contacts.
Note
Do not disassemble the phone under warranty, otherwise it will be applicable for it.
Search
Is the advice useful?