Advice 1: How to do the lift Fields

The vehicle is not a Rover and terrain is far behind the UAZ. To improve cross requires, first and foremost, the installation of large wheels and lift the suspension. Please note that the Elevatorvannoy the Field significantly reduces the resource of suspension parts, chassis parts and transmission. So the point of me doing the lift is only with frequent use Fields for serious off-road.
You will need
  • Tie suspension springs (short for front and long for rear). Set carob and spanner wrenches with socket set. Bulgarian. Vise. Jack. For the rear suspension: springs VAZ-2104 and spacers for the rear springs on the VAZ-2101-2107, shocks from Gazelle or imported, the upper longitudinal thrust from IZH-2126. For the front suspension: springs from Chevrolet Niva, shocks from the same car or imported, pressure washer-sealed ball bearings as spacers.
Instruction
1
Before starting work, support the Cornfield on the lift. In the absence of a lift Jack and set the stands under the body. Hanging out a car reduces the risk of it falling and speeds up the process of the Elevatorunit.
2
Raise the rear of the car to maximum height and lock. Fixing a car should be reliable, because the production of work the machine will greatly swing. Unscrew from the rear axle thrust limiter of the braking force, tee the rear circuit of the brakes, lower and upper mounts of shock absorbers. The tee off. Remove the shock absorbers and rear springs. If necessary, disconnect the fixing of the handbrake cable.
3
At the top cups of springs, install the spacers, put the new springs. Jack raise the rear axle up to the height needed for installation of the shock absorber. Installing new rubbers in the shock absorber, place it. Screw first the upper attachment then the lower one, but do not tighten completely. The shock absorber before installing the pump, why squeeze it 6-7 times before it stops. Lower the rear part of the car to the ground.
4
Remove both upper torque rod from the rear axle. Install the new torque arm, not wrapping the final bolts. Jack up the rear axle for the gear. Turning the bridge screw thrust to the body. Finally do not over tighten. Lower the rear axle. A little jump on the rear bumper, that established gum shock stood up and turned freely.
5
Not raising the vehicle, completely tighten all loose nuts. Reinstall the thrust limiter of the braking force and adjust it. Tee extend with a suitable hose and reinstall.
6
Loosen the nuts on the front wheels. Raise the front of the car and reliably fix. Remove the wheels. Clean from dirt ball bearings, levers and shock absorbers. Remove the springs. Remove the shocks by removing the upper and lower mount. Remove the front stabilizer bar by disconnecting its attachment to the body and lower control arm. To improve cross, do not put it back. Unscrew the bolts attaching the upper and lower ball joints. Remove the springs, releasing them from their ties.
7
Install the coupler on new springs and the springs on the car. A Jack, raise the lower suspension arms to the height required for installation of the absorbers. Setting on the dampers new rubber bands, put the shock absorbers. From the top of the bump stop cut off 60-70% of its height. Tighten the ball stud to the lower arm. The upper ball bearing assemble the spacer 13 of the clamping plates with water between them. Use long bolts to attach upper ball joint to the upper arm. If the necessary stability Fields on the pavement, set the front stabilizer.

Advice 2: How to make a Field

Cars of the domestic automobile industry are very popular. This is due to the low price of these cars. For example, lovers of fishing and nature trips can buy a vehicle. This Russian SUV is able to overcome most roadblocks. How to make a Field more adapted to your busy vacation?
You will need
  • Additional lights on the roof, winch, roof rack, paint, primer, tools, cutter branches, full-size spare wheel, manual operation of the vehicle.
Instruction
1
First and foremost, pay attention to the bodywork and paintwork of your Fields. The car is designed to overcome the road obstacles so the body can easily be scratched or broken. If time does not treat the damaged area, that can start corrosion, which will lead to rot. Carefully inspect the entire body. Best drive on lifts to examine the underbody. It is the most susceptible to corrosion. If on the back you'll find pockets of incipient corrosion, clean them to bare metal, and then brew. Then cover with primer and paint. Also it is useful to treat car rust inhibitor.
2
The next step is the inspection of the suspension. Thanks to the proper suspension of Niva is so easy to overcome obstacles of various kinds. At first, measure the clearance. In the user manual to your car find the value of the normal clearance, it can vary depending on what your wheelbase. If the clearance is too low, the car can sit on the bottom in mud or snow, if too big, then bury the wheels. The springs should be without chips and cracks. Measure their length. Inspect the shock absorbers. They should be no traces of stains. If any, put new shock absorbers. best suited gas.
3
If you often go on nature, we should care also about some of the devices. Install the winch, it will help to get your car if you get stuck. The winch should be secured to the supporting structure of the car then to the front beam. Install shut-off valves of the branches. They are mounted from the edges of the bumper to the edges of the roof. The roof rack will allow you to carry cargo of various kinds. Take care of a full-sized spare wheel. Additional lighting will help the car to move in the dark. Additional lights are best placed on the roof.
Useful advice
After lifevania suspension to re-align the wheels.
Search
Is the advice useful?