Advice 1: How to make a quiet Field

Work on soundproofing the Fields easier to perform in a fully disassembled car. Therefore, quality work with your own hands takes a lot of time. Professional insulation involves the use of several types of material for each section of the car body. When choosing the materials we prefer self-adhesive materials.
You will need
  • noise suppression foam otkrytiy material with a protective film aluminazirconia 12 mm thick (No. 1);
  • - vibration damping bitumen material with protective aluminum foil with a thickness of 2 mm (No. 2);
  • - bituminous vibration damping laminate thickness of 4 mm (No. 3);
  • - bituminous cardboard with a shock-absorbing layer with a thickness of 1.5 mm (No. 4);
  • - bituminous vibration damping laminate with a thickness of 2 mm (No. 5);
  • - glued together the materials No. 1 and No. 5;
  • - Guerlain;
  • - foam thickness 1 cm
Instruction
1
All surfaces exposed to noise, at first carefully measure. Then cutting purchased materials and adjust the place of the cut out pieces. Pasted over the surface degrease with gasoline. All materials, except for # 1, once attached, heat with a Hairdryer. To facilitate cutting of the material No. 3 pre-heat it.
2
Remove the gas tank. The floor under it paste over material No. 2. For dismantling the ceiling, remove the windshield and rear side glass. Regular fiberglass completely remove the liberated surface of the brush. Glue material No. 4, and on top of it – material No. 1.
3
The gear housing glue material No. 2 from the inner side. It will have to first remove the transmission and clutch. Compartment side, remove the factory insulation and glue material No. 3. Additionally, to reduce noise loop transmission. Handle the control transfer box wrap material No. 5.
4
The rear fenders first seal material No. 3, and the top material No. 1. Amplifiers paste over the material No. 5. The plastic trim of the rear fenders from the inside, seal foam with a thickness of 1 mm. the rear wheel Arch glue material No. 3.
5
Engine compartment up to the spars glue material No. 2. The leaves stick butt jointed without overlap. Try to glue the space behind the engine. The same material paste over the body of the air intake heater. The hood is decorated with material No. 6.
6
From the doors, remove the standard insulation, clean the metal from corrosion and apply material No. 4, and on top of it to material # 1. Rear side door trim glue porous polyethylene. On the plastic trim of the rear doors optionally attach a foam thickness of 1 cm.
7
With the inner part of the heater unit and ducts, as well as all the plastic parts and interior glue material No. 5. The very beauty from the inside glue the material No. 3 of the lower frame of the windshield to the back door. On top of all of the installed noise insulation apply adhesive Guerlain. Mats wrap material No. 5
8
When you build the car solivita new holes and use fasteners of greater length, where necessary.

Advice 2: How to make a Field

Cars of the domestic automobile industry are very popular. This is due to the low price of these cars. For example, lovers of fishing and nature trips can buy a vehicle. This Russian SUV is able to overcome most roadblocks. How to make a Field more adapted to your busy vacation?
You will need
  • Additional lights on the roof, winch, roof rack, paint, primer, tools, cutter branches, full-size spare wheel, manual operation of the vehicle.
Instruction
1
First and foremost, pay attention to the bodywork and paintwork of your Fields. The car is designed to overcome the road obstacles so the body can easily be scratched or broken. If time does not treat the damaged area, that can start corrosion, which will lead to rot. Carefully inspect the entire body. Best drive on lifts to examine the underbody. It is the most susceptible to corrosion. If on the back you'll find pockets of incipient corrosion, clean them to bare metal, and then brew. Then cover with primer and paint. Also it is useful to treat car rust inhibitor.
2
The next step is the inspection of the suspension. Thanks to the proper suspension of Niva is so easy to overcome obstacles of various kinds. At first, measure the clearance. In the user manual to your car find the value of the normal clearance, it can vary depending on what your wheelbase. If the clearance is too low, the car can sit on the bottom in mud or snow, if too big, then bury the wheels. The springs should be without chips and cracks. Measure their length. Inspect the shock absorbers. They should be no traces of stains. If any, put new shock absorbers. best suited gas.
3
If you often go on nature, we should care also about some of the devices. Install the winch, it will help to get your car if you get stuck. The winch should be secured to the supporting structure of the car then to the front beam. Install shut-off valves of the branches. They are mounted from the edges of the bumper to the edges of the roof. The roof rack will allow you to carry cargo of various kinds. Take care of a full-sized spare wheel. Additional lighting will help the car to move in the dark. Additional lights are best placed on the roof.
Search
Is the advice useful?